Skip to main content

bond0 interface

In the example below, the bond0 interface is the master (MASTER) while eth0 and eth1 are slaves (SLAVE). Notice all slaves of bond0 have the same MAC address (HWaddr) as bond0 for all modes except TLB and ALB that require a unique MAC address for each slave.

# /sbin/ifconfig
bond0 Link encap:Ethernet HWaddr 00:C0:F0:1F:37:B4
inet
addr:XXX.XXX.XXX.YYY Bcast:XXX.XXX.XXX.255 Mask:255.255.252.0
UP BROADCAST
RUNNING MASTER MULTICAST MTU:1500 Metric:1
RX packets:7224794 errors:0
dropped:0 overruns:0 frame:0
TX packets:3286647 errors:1 dropped:0
overruns:1 carrier:0
collisions:0 txqueuelen:0

eth0 Link
encap:Ethernet HWaddr 00:C0:F0:1F:37:B4
inet addr:XXX.XXX.XXX.YYY
Bcast:XXX.XXX.XXX.255 Mask:255.255.252.0
UP BROADCAST RUNNING SLAVE
MULTICAST MTU:1500 Metric:1
RX packets:3573025 errors:0 dropped:0 overruns:0
frame:0
TX packets:1643167 errors:1 dropped:0 overruns:1 carrier:0
collisions:0 txqueuelen:100
Interrupt:10 Base address:0x1080

eth1 Link encap:Ethernet HWaddr 00:C0:F0:1F:37:B4
inet
addr:XXX.XXX.XXX.YYY Bcast:XXX.XXX.XXX.255 Mask:255.255.252.0
UP BROADCAST
RUNNING SLAVE MULTICAST MTU:1500 Metric:1
RX packets:3651769 errors:0
dropped:0 overruns:0 frame:0
TX packets:1643480 errors:0 dropped:0
overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:9 Base
address:0x1400

Comments

Popular posts from this blog

mplayer-gui error : Error in skin config file

After installing mplayer-gui package, I can't start it.

$ gmplayer MPlayer 1.1-4.8 (C) 2000-2012 MPlayer Team mplayer: could not connect to socket mplayer: No such file or directory Failed to open LIRC support. You will not be able to use your remote control. Error in skin config file on line 6: PNG read error in /usr/share/mplayer/skins/default/main Config file processing error with skin 'default'
After googling a bit, I found out that it was due to the png files in dir /usr/share/mplayer/skins/default. This is the default skin directory. To fix this error, I have to install ImageMagick package because I want to use the convert program to convert all of the png files to format png24. Thus, cd /usr/share/mplayer/skins/default; for FILE in *.png ; do sudo convert $FILE -define png:format=png24 $FILE ; done
Rerun gmplayer and all should be fine.
Have fun!
UPDATE (02-10-2017)

It doesn't work on Ubuntu 16.04 (xenial) but there's a workaround here.

You can update your syst…

Moving your mysql database to another hard disk

Recently, my server's only hard disk was almost full. I bought a new hard disk with bigger size and I decided to just add it as a second hard disk. Since I need to move it to the 2nd hard disk, I need to find a proper way to move the db with minimum downtime. So I googled around and found a solution.
First, I needed to format the 2nd hard disk and I chose xfs as the filesystem. I created 2 partitions using Linux's fdisk for this task. First partition is 10 GB and 2nd one is around 900 GB. That's approximately added up to 1 TB. Then I mounted the 2nd partition in current partition eg /media/hd2 as follows:
mount -t xfs /dev/sdb5 /media/hd2
where /dev/sdb5 is the partition and /media/hd2 is the mounting dir.
Stop mysql db before doing anything:
service mysql stop
Afterthat, I copied the entire db to newly mounted hard disk:
cp -rv /var/lib/mysql /media/hd2
It will take a while if you have huge databases.
Then, change the ownership of the dir to user and group of mysql:
chown -R mysql:…

Transparent proxy with squid 2.6

I have upgraded my squid from 2.5 STABLE13 to 2.6 STABLE18. Transparent proxy is setup differently in this version. You need this directives in squid.conf (usually in /etc or /usr/local/etc or /usr/local/squid/etc, check with your distro).

acl our_networks src 192.168.2.0/24 127.0.0.1
http_access allow our_networks
http_port 192.168.2.1:3128 transparent
always_direct allow all

where 192.168.2.1 is your proxy server IP address.


If you have flushed your iptables, create new rule:

iptables -t nat -A PREROUTING -i eth0 -p tcp –dport 80 -j REDIRECT –to-port 3128

where 3128 is the port where squid is running.
References:
http://www.deckle.co.za/squid-users-guide/Transparent_Caching/Proxy